Lot 4 Each, 48" Aluminum T Track 3/4" by 3/8" Slot, Accepts 1/4" Hex Bolts, 1/4" or 5/16" T Bolts, Countersunk Holes Every 6" 112134

So many uses...too many to list. This price for 16' of T Track can't be beat. It is well made and easy to cut with a jig saw or miter saw. It fits precisely in a 3/4" W x 5/8 D dado and fits standard t-bolts. As another reviewer noted, finding the correct screws was a bit of hassle, so it would have been helpful if this came with screws or a note about the screw size needed. That was a minor annoyance, however. These tracks may not be as hefty as Kreg or Rockler tracks, but these aren't necessarily designed to hold a lot of weight or be installed with large screws, so in the right application that shouldn't matter. If you're using them for typical woodworking projects, such as workbenches, jigs, sleds, etc., they should work perfectly. I plan to buy more when I've used up what I have.

I have been using T-tracks for various projects in my new shop. I have bought t-tracks from both specialty woodworking stores as well as unknown sellers on ebay. The price and quality (consistency) varies from place to place. About 6 months ago I found the tracks from Taylor tools to be both consistent and high quality for a very fair price. As a matter of fact they had the best price for the 4x48" package which included free shipping. All the four tracks were 0.75 +-0.005 inches without any benor warps. This makes it easy work of using these in jigs and other accessories in the shop. So I bought another set of four again and I was not disappointed. I highly recommend these from Taylor Tools

This product does not have quite the "fit & finish" of the Kreg track, but is plenty good for normal shop fixtures. I'm using it in table tops to support fences and various holddowns, etc., and it works a charm! I will be ordering more when my present stock is used up. For the really fancy stuff (like my miter/radial arm saw station fences I use this track for the table surface tracks that allow the fences to be adjusted, and the Kreg Top Trak for the fence top to support flip & production stops.

Impressed with the quality of the material and the craftsmanship (all rails are the EXACT same length and width), but the packaging left something to be desire. All four of the rails were dinged on the ends (like perhaps they had been dropped), rendering that end useless, because you can't get a hex or J-bolt in the slot on that end. I'll reach out to the manufacturer to see what we can do to rectify this. Anxious to get these in use. Fair price. Well made.

These work great to hold down flexible solar panels to the roof of my utility trailer. Along with a little bit of VHB tape and I can slide the solar panels right on. These are nice light aluminum and I had and strange issues like rust or anything that would indicate they aren't actually aluminum. Haven't had any corrosion/oxidation either but that is because I followed my own advice: Pro-tip: If yours are exposed to the elements, there are quite a few aluminum protectants out there, choose one and use it. These are likely anodized well but the protectant won't hurt anything. You can even get protectants that will remove oxidation if it's begun to set in on yours which you can shine them up back to new but better to just protect them out of the gate.

Great product, I am using these rails for a clamp down system on my CNC Router table. I needed (6) rails 32" long so I cut these at 32" and used the (4) 16" pieces end to end to make up the other (2) 32" rails. I added extra drilled and countersunk holes at the ends to add extra clamping force. The extrusions were very high quality and of exacting measurements. They averaged .746 in width and were exactly 48" long. I did not accurately measure the thickness but with a precision scale they were 3/8". 1/4" hex bolts fit perfectly, as did 1/4" T-Nuts.

The only version of t-track that works for my project. Great product and great service. Had an issue with first shipment. It was immediately taken care of. Thank you...

I used these to make a hold down bed for my benchtop CNC. The have a decent fit and finish and are quite strong. All of my accessories fit in the tracks and slide easily. Would definitely purchase again.