All-in-One 24MP Film Scanner with Large 5" Display & HDMI, Converts 35mm/126/110/Super 8 Film & 135/126/110 Slides into Digital Photos, Built-in Memory (FS71)

This worked great. It was fast, and picture quality was awesome. I got through at least a thousand slides in one evening. I recommend this product. So easy to use.

I finished scanning over 8,000 negatives (up to 35 years old), including one Black&White set of negatives. On the whole, this is a really awesome little gadget. It does all the basics, very efficiently, and with a very minimal learning curve. I managed to complete my scanning in less than 6 weeks, working basically on weekends (maybe 40-60 hours tops). It really beats having to scan your prints, using your home printer, at the rate of 3 minutes per print, assuming you have a decent copy of your prints. With this machine, it takes longer to get the negative out of its current location, identify the proper side, than to load it and make the digital copies. I have not tried any of the other similar products, so I'm not sure how they compare. What I've used: - Different negative types (mainly 35 mm, color & black&white, some 110, some 126) - it has all of the adapters - A perfect little dust brush to clean the interior glass surface on a regular basis (particularly if you own cats/dogs in the house). - The brightness setting for particularly under or over-exposed pictures. Keep in mind that it won't make the picture better, just lighter or darker. What you'll need: - an SD card to load your scanned images, which you'll then need transfer elsewhere A couple of things that could be improved: - With the included adapters, you can only scan the equivalent of a 4x6 ratio, which you can easily adjust horizontally (left or right) as you see fit, but which you cannot adjust vertically (top or bottom), meaning that it crops the top and bottom for you systematically. The only way around the vertical cropping is not to use the adapter and feed the negative without the adapter, at the risk of not positioning it quite right. I only did that for a few pictures. - It would have been nice to have a USB cable into your computer directly and skip having to scan the negative onto an intermediary SD card. I guess it was fine though, the SD card served as my backup until I copied the photos to alternate devices. However, the SD card adds on to the overall price of the project, but you can repurpose the card later. - The default color may not be perfect, although who knows whether it's the machine's fault, or the deterioration of the colors on the negative strip itself. I had a hard time using the feature without the original print for comparison. A few things to keep in mind: - If your negatives are in good shape, and were high quality to begin with, this machine will work beautifully. If your negatives are bad, no machine in the world will make them better. - If you need a poster size high-quality image, then you might consider taking those negatives to a professional. But for 4x6 prints, this machine is fine. For perfection, you'd have to invest in a much fancier, pricier and more time-consuming device. If you have the time and money, that would be ideal. In the meantime, this little machine is pretty nice.

Can’t recommend highly enough!! I looked through a ton of similar models and am thrilled with this one. It has done a great job on my grandpa’s 135mm slides from 1940s-1970s. It’s been awesome to have the option to digitize negative film also! Very user friendly and dependable for a great price

Does the job nicely. It's quick and pretty accurate. It does cut off a little bit of the 35mm slide but not enough to make much difference. Transferring the images to my Mac is easy and quick. The internal memory only holds around 15 images but after transferring them it's easy to delete the memory and start again. I wouldn't use it much for editing the images. Just transfer to your computer and use your editing software for that. The only quirk I noticed is that when a slide is very dark, the screen flickers like it's about to crap out but once you remove that slide everything goes back to normal. This probably isn't for a professional but it's great for average home use to convert your slides.

This is a great scanner for the price. I tested it on various slides, on different film types, too light or dark, with a color cast, etc. I'm a picky photographer. The scanner automatically brightened a dark slide to be exposed properly without being "blown out" (totally white), but overexposed slides came out dark; again, I used a photo editor to fix the image. I only scanned a few color negatives, so I can't comment in general... but one underexposed negative (which should be too dark) scanned too light, with no true black. So, again, a photo editor is your friend for improving some scans. The images from slides were very sharp. I could see the film grain in the scanned image. The cable is fairly short. You might need a longer USB-A to mini-USB cable. The unit gets power from the USB cable. If you don't have a computer, you'll need a mini-USB power supply brick that plugs into a wall outlet. (This means you can use the scanner on a laptop.) The scan was almost instant. (Unlike other film and paper scanners I've used, there's no light/scan bar that moves across the image.) From a 35mm slide I got a scan file 6000x4000 pixels, 6.2 MB file size. (The 6.2MB will vary depending on how complex your original photo is... that's how JPGs work.) A bit of the edges were cut off, but this was usually fine. The color adjustments are in steps and a bit coarse (0, 0.5, 1.0, etc.; you can't pick a value between). They worked pretty well for big changes, but I preferred a photo editor and a computer screen. You'll need to understand that these three settings -- red, green, and blue -- can be negative to add the opposite color. For instance, yellow is the opposite color of blue. If the image is too yellow, you can't reduce yellow; you have to increase blue. If you don't want to fiddle, your photo editor probably has a "fix color" setting you could try on the saved image. Note that the scanner "remembers" the previous color adjustment... if you don't want that, reset each color after you finish one slide or you capture the next slide. The single negative holder is really frustrating because it doesn't hold a strip of film tightly... so, as you try to put the film strip in the holder into the scanner, it can shift and make the scan off-center. I've ordered a negative holder that holds a whole strip of six photos; that should be a lot easier! Tip: You don't need to open the single slide holder to put a slide in it, then close it. Instead, while the holder is closed, try pushing the slide in from the left end, as in the photo. To avoid touching the film (which will make a fingerprint that can eventually eat into the film!), use your fingernail to scoot the inside of the slide mount left and right. Vertical photos have to be turned to go into the scanner horizontally. I rotated them with the lossless JPG rotation in the amazing free Irfanview app... or you could open the image in a photo editor, which takes a bit more time. On my Windows 11 desktop, when I went to "Connect to PC" on the scanner menu, the File Explorer app opened. It (in this case, the F: drive) showed the photos in the scanner memory. You'll need to transfer the photos yourself if you want to keep copies after you unplug the scanner. If you aren't familiar with File Explorer, you can probably use another app that copies the photos for you. Kodachrome slides scanned just fine. (Kodachrome is a problem on some scanners.) To help avoid dust spots, insert the cleaning brush through the slot once in a while (dust wasn't a problem for me, though). After you line up the film in the holder but before you put the holder into the slot, use a can of compressed "air" to blow away dust (invisible or visible). If spots bother you after you see the scanned image on a computer screen (where it's much easier to see the spots), use something like the Healing Tool in the powerful free GIMP editor (gimp.org). If you don't line the film up exactly, the scanned image will have a black bar at one side. I had to move the slide holder while it was in the scanner to get rid of the bar. Luckily, after pressing the Capture button, the image on the scanner screen is "live": As you move the slide holder left and right, you can see the black bar disappearing. A scanner like this will be designed to cut off a bit of the edges so you normally won't see a black edge on any side (which would be caused by scanner scanning some of the opaque cardboard slide mount). Some cardboard slide mounts were too thick to fit in the holder easily. A lot of the slides were too thin; they shifted left and right as I handled the holder... I had to carefully hold it flat as I put it in the scanner. Tip: I scanned an underexposed negative, which should come out dark. But the scan was too bright: a bit "washed out", with no true black. I opened the scanned negative in a photo editor and checked the amount of red, green and blue in the scanned file; it didn't have any true darks. (The photo editor's histogram shows this: the left side of each curve, which shows how much of the darkest shade of each color is in the scan, shows no dark colors.) I used the editor to "drag" the left edge of each curve to span the whole width; that improved the scan a lot. (Note: don't just turn down the brightness in the editor because you'll probably lose the brightest colors. Spread the histogram curve so you'll have dark darks and bright whites.) I've included the original scanned photo and the one darkened with my photo editor. Overall, for the price -- even with irritations like trying to align the film in the holder -- this scanner is amazing.

This is an excellent product, easy to set up and use, with great results. I had previously tried scanning old slides with an Ion “slides forever” device, but the quality was terrible because of low resolution. This Magnasonic is more expensive but there’s no contest when it comes to quality. The resulting images are clear and bright. You have to feed slides manually but it’s quick and easy - each slide pushes the previous one out the other side. Exposure or colour can be adjusted when (rarely) needed, though not in detail. The device has a very small internal memory so it’s advisable to buy some standard SD cards for bulk processing. Important note: it will only work with lower capacity cards - 2GB recommended (which will hold a few hundred images). Files can be transferred to computer via card reader or direct from the device. No software needed.

高解像度は期待しない事〰️✨ あくまでも大量のフィルムから必要なモノをチョイスし軽い気持ちで電子化する用と考える❗

Very good item, highly recommended.

It's easy to use and good quality

gaf een beter resultaat dan verwacht, heel tevreden mee